Look at any of the top car audio subwoofer amplifier models available from specialty retailers. You’ll find that most include an option for a remote level control or bass boost function. Being able to fine-tune the output of your subwoofer system is great for those times when you want to rock out to an amazing song or calm things down so you can talk to a passenger easily. This article will look at how the subwoofer level controls on source units, digital signal processors and car audio subwoofer amplifiers work.

You Can’t Get More than Full Power

Before we dive into the different adjustment options, consider that the maximum output you’ll get from your subwoofer system depends on the excursion capability of the sub and the maximum power available from your amplifier. You can’t get more bass by increasing the signal to the amplifier when it’s already optimized to make maximum power at full volume. With that said, you can get to full power sooner and increase the amount of bass relative to the midrange and high-frequency speakers in the vehicle. Remember that you may need to limit how high you turn the volume control on the radio if this is how your system is configured.

Think of your subwoofer system like the engine in your car. Once you’ve put your foot to the floor and the engine is making as much power as it can, there’s no way to get more power without some significant modifications to the vehicle. If you want more bass than is being produced by your car audio system, return to the retailer that installed the system and talk to them. You may need more subwoofers, larger subwoofers, a different enclosure, a more powerful amplifier or some combination of these items.

Subwoofer Level Controls in Car Audio Source Units

Almost every source unit on the market with electronic crossovers also includes a subwoofer level control function. This control adjusts the level on the subwoofer preamp output RCAs relative to the level on the front and rear RCAs. These source units are configured to work two ways.

The first example we’ll look at is configured the same as the Sony XAV-AX7000 that the BestCarAudio.com team reviewed here. In the subwoofer adjustment menu, when the level is set to 0, the subwoofer output level is the same as that of the front and rear preamp outputs. If you increase the subwoofer level to 10, the output on the sub preamp output increases. This configuration results in you reaching the maximum output capability of the subwoofer preamp outputs with the volume control set to 38 instead of 49. Turning the volume up higher will produce distortion on the sub preamp output. You can also turn the output down to -10 if you find there is too much bass. Lowering the signal has no adverse effect on the outputs.

Other companies configure their subwoofer level controls on a scale of 0 to 10 or 0 to 20. Though the labeling varies from brand to brand and potentially model to model, setting the output level to its highest setting would result in the preamp output being maximized without distortion when the volume is maximized. This configuration prevents the outputs from distorting when the volume is cranked. In an ideal world, the radio’s sub output adjustment labeling would be something more akin to -10 to 0.

Level Controls in Digital Signal Processors

Just as with a source unit, there’s an upper limit to how much voltage can be produced on a digital signal processor’s output. If the DSP is built into an amplifier, maximum output is determined by the voltage and current capabilities and the impedance of the subwoofer(s) connected to the amp. If your system uses a stand-alone processor, then it can likely produce 5 or 8 volts of signal on the RCA output jacks. Most signal processors include a subwoofer level option that can be adjusted with one of their optional remote controls. As a key part of the system calibration process, the technician working on your audio system will need to ensure that the signal remains clean and undistorted when the volume is maximized.

A unique option that ARC Audio includes in its PS8, PSM and PS8 PRO series signal processors is a configurable level control. When the optional LR1 remote is added, your technician can configure which channels it affects and by how much. If you want the LR1 to act as a sub control, it can be assigned to adjust over a range of -20 to 0 dB and be configured to work with the outputs that feed the sub amplifier. The software configurability means that this remote could also serve as a master volume control for the entire system, as a center channel level control or rear-fill speaker level adjustment.

Issues with Adjusting Subwoofer Output Level

Some digital signal processors offer a bass EQ control aside from their graphic or parametric equalizer. These adjustments are more likely to be found in processors that are compatible with the Maestro AR to integrate directly with factory-installed source units. In most of these cases, the bass EQ is a shelf filter that adds a specific amount of boost below a configurable frequency.

There is a problem with adjusting bass output this way. Suppose your audio system is calibrated to a target response curve, and the crossovers are set properly. In that case, the point at which the subwoofer’s output crosses over with the midbass driver’s output should be at the -6 dB point to sum flat in terms of phase and frequency. If you turn the bass up, that crossover point changes. This mismatch can result in some bass frequencies sounding as though they are coming from the front of the vehicle and some from the back.

In reality, applying the shelf control shown earlier to both the subwoofer and the midbass drivers maintains this phase and amplitude relationship, so your audio system sounds its best.

Bass Boost Versus Subwoofer Level Control

Many subwoofer amplifiers include a bass boost control. These are typically a narrow-band equalizer circuit that’s centered around 45 or 50 Hz. Some entry amplifiers have a switch that adds 6 or 12 dB of boost at this frequency, while others have an adjustment potentiometer that allows for a variable amount of boost, usually up to 12 or 15 dB.

Fancier amplifiers add frequency and Q-factor adjustments to the boost level control to allow your installer to fine-tune the system further. Used gently, these adjustments can add some low-frequency emphasis to a sealed subwoofer enclosure to make it more fun.

While these boost circuits can make listening to your music a lot of fun, when used excessively they typically don’t result in smooth and natural sound. If you want your car audio system to reproduce a recording of a set of drums in a way that makes them sound real, lots of bass boost isn’t a great solution. If you want to rock out with your friends to some rap, dance or techno, it can be awesome!

For technicians setting up an amplifier that includes a remote bass boost or remote level control, he or she will need to ensure that the system can play without unwanted distortion with the volume on the radio maximized and the control turned all the way up. The crossover adjustments will need to be optimized for the system’s typical listening preferences to sound its best.

If you’re considering adding a subwoofer system to your vehicle, an upgrade we highly recommend, then drop by your local specialty mobile enhancement retailer today. They can design and install a solution that sounds great and delivers the performance you want. If you listen to many different kinds of music, be sure to ask them about including a remote subwoofer level control in the system design.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

If you’ve browsed amateur car audio groups on Facebook, you’ve likely seen someone post that they have “set the gains halfway” on their amplifier. Their misguided theory is that this setting will limit the maximum amount of power the amplifier will produce. Saying this in the presence of a professional installer is the best way to announce that you don’t really know how the sensitivity control on your amplifier should be set to optimize its output capabilities and minimize the noise in your car audio system. Confused? No worries, we’re here to help explain it all.

What Does the Gain Control Do on a Car Audio Amplifier?

Imagine a world where every car radio provided the exact same preamp output voltage at full volume. If you play a song that reaches the maximum allowable recording level for the medium you’re using (CD, cassette, digital audio file or whatever), and you have the volume control on the radio turned up all the way, then you might get a signal that peaks at 2 volts. In this scenario, every amplifier on the market could be configured to produce its maximum rated power when it sees 2 volts of input signal.

In reality, the sources we use to play our music vary dramatically in their output capabilities. An iPod might produce 330 millivolts. An inexpensive radio is likely capable of producing around 2 volts, and a higher-end multimedia receiver or a good DSP might reach or exceed 5 volts. Ignoring the need to balance the relative output level between a subwoofer and midrange speakers (for now), we need an amplifier that can produce full power with signals that vary from few hundred millivolts up to more than 5 volts. The sensitivity control on car audio amplifiers is the adjustment that lets a properly trained technician configure the amp to make its maximum rated power from a variety of sources.

Why Setting Gains Is Crucial

Let’s start with a simple example. You’ve had a subwoofer system installed in your vehicle and you’ve chosen a 500-watt amplifier to drive a pair of subwoofers that are rated to handle 250 watts of power. In the simplest scenario, the technician installing the system should set the sensitivity control on your amplifier so that the amp clips a tiny bit when you max out the volume on a radio that can produce 2 volts of output. If the amplifier is rated to work with sources ranging from 150 mV to 4 volts, then a setting around 2 volts or around 20% from its minimum sensitivity will be pretty close. The technician will check to make sure that the type of music you enjoy will play loudly, then send you on your way to enjoy your upgrade.

Suppose you decide at a later date to update your audio system with a premium multimedia receiver that includes Apple CarPlay and Android Auto. In that case, you might find that it can provide 4 or 5 volts of output on the preamp connections. With this unit in place, the sensitivity controls on your amp are too high, and it would be easy to drive it into clipping. The amp needs to be turned down to just about its lowest sensitivity to make full power at full volume.

The Drawback of Too Much Gain

If you are attentive to listening for significant distortion being added by pushing your amp to the point that it clips, then theoretically, you could leave the sensitivity control at 20%. By lowering it, the amp will add less unwanted noise to the system, and you don’t have to worry about how high you turn the volume. That said, it’s hard not to want to turn the volume up when your favorite song comes on. Noise isn’t much of a consideration with a subwoofer amp, but low- to moderate-quality amplifiers can add a lot of hiss with the gains cranked up when driving coaxial or component speakers.

Amp Gains and Maximum Power Delivery

The correlation between the setting on your amp and how much power is produced is based purely on how much signal is sent to your amp. If you have an extremely low-voltage source like an iPod, then the amp may need to be set at 75% to 85% of its maximum. In this case, turning the amp back to 50% WILL reduce how much power it produces. If the amp is optimized at 25%, then turning it to its minimum will also reduce power.

To state that an amplifier is set “halfway” ignores the variables of source unit output voltages, volume settings, source material loudness, system equalization and the impedance of the load connected to the amp. If you only need 10% of an amp’s gain capabilities, setting it to 50% doesn’t make sense, and it certainly doesn’t limit the amplifier to half its power production capabilities.

It’s Much More Complicated

The sensitivity control is also used to balance the relationship between speaker output levels in actively filtered car audio systems. If you have a 500-watt amplifier for your subwoofer and a 50-watts-per-channel amplifier for your door speakers, setting both so that they clip simultaneously might not deliver an overall system balance that’s ideal. Of course, the design of the audio system matters. If you’re running one 8-inch sub in an acoustic suspension (sealed) enclosure or a pair of 12’s in a bass-reflex (vented) enclosure also plays a huge role in how things will be configured. You also need to take into account that the amp for the door speakers is likely only going to play down to about 80 Hz. Crossover settings complicate the calibration process even further and render tools like an oscilloscope useless without the proper test tracks.

Let’s wrap this up with another example. Say you’re using a high-quality digital signal processor that can provide as much as 8 volts of output to your amplifier. It’s quite likely that you can provide more than enough voltage to drive that amp to or beyond the point that it will add distortion from clipping to the output, even with the amp gain set to its minimum setting. Consider the flawed logic of saying, “I’ll only get half the power if the set the gain halfway.” The reality is, the amp will likely reach its maximum output capability at half to three-quarters of the maximum volume on the radio. If you turn the volume up further, you are just adding distortion to the output signal and risk overpowering the speakers or subwoofers.

Our second and equally illogical example would be a scenario where you have an amplifier that’s capable of overpowering your speakers. Imagine a subwoofer rated for 200 watts connected to an amplifier that could produce 1,000 watts. Is “setting the gain at half” going to protect this sub from damage? If you have an audio source with extremely limited output voltage, maybe. Suppose you have a source capable of producing more than a couple volts, then nope. You’ll likely destroy it.

If you’re starting to get the impression that setting the gain correctly in a car audio system with multiple amplifiers isn’t as simple as you first thought, then this article has served its purpose. It’s a complicated process that requires the technician working on your vehicle to consider many factors. More importantly, if you’ve damaged a set of speakers by overheating the voice coils, you’ve overpowered them. Too much power produces too much heat. That’s it. Period. There’s no other reason this happens. It doesn’t matter how your amp was set. You melted them.

If you’re having problems with your car audio system, look for a qualified specialty mobile enhancement retailer in your area to help configure your system properly or help you choose a combination of components that will work together to deliver the performance you want.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

When designing and integrating high-performance speakers into your car or truck, your local specialty car audio retailer might suggest choosing an amplifier or signal processor that includes a bandpass crossover. If you aren’t used to designing speaker systems, a task that most consumers don’t concern themselves with, then the term bandpass might be confusing. Please don’t fret; we’ll explain what it means and why it’s necessary to extract the best performance possible from your speaker upgrades.

What Are Crossovers?

The theory of a perfect speaker that produces the entire audio range, from a single driver, at an adequate output level with no directivity, is so far from reality that the concept alone makes a speaker engineer’s eye twitch. As such, we need to use speakers of different sizes to cover the audio spectrum. In the simplest of systems, we need a woofer to produce bass and midrange frequencies and a tweeter to produce high frequencies. Since most tweeters are rarely capable of reproducing information below 2 kHz with significant output, we need to block that information. We use what’s known as a high-pass crossover to pass only high-frequency information. Looked at another way, a high-pass filter blocks low-frequency information from going to your speaker.

Once we have routed high-frequency information to our tweeter, we don’t need the woofer to reproduce those sounds. So, the technician configuring our audio system will apply a low-pass filter to the woofer at the same frequency. This filter passes low-frequency audio information below our crossover point to the woofer.

What Is an Electronic Bandpass Filter?

If we decide that we want to further upgrade the audio system with a subwoofer, we’ll need more filtering. Subwoofers are great at reproducing audio frequencies below about 80 Hz. Most don’t do a good job with midbass and midrange information. As such, we want to block frequencies above about 80 Hz from going to the sub. We’ll use an 80 Hz low-pass filter to accomplish this task.

Now that we have a speaker dedicated to reproducing bass, we don’t need our woofer to play those frequencies. We can apply a high-pass filter to the woofer to block audio information below 80 Hz.

The graph you see above is called a bandpass filter. It passes audio within a specific band of frequencies. In this example, our bandpass filter passes audio information between 80 Hz and 3 kHz.

Some car audio systems add a fourth set of speakers in the form of a small midrange driver. In most cases, these speakers are mounted higher in the doors or the dash and focus on information from about 300 Hz up to where the crossover takes over. In a four-way audio system design, we can now move the low-pass crossover on our woofer to 300 Hz and run the mid from 300 Hz to 3 kHz.

Proper Crossover Configuration Is Crucial

There is a lot more to setting crossovers than just picking some arbitrary frequencies that look good on a graph. The values depend on the speaker’s low-frequency capability and its directivity characteristics. The installer calibrating your audio system also needs to consider the physical power-handling limitations of speakers and how loudly the system will be played. Quite simply, it’s not an easy task, and the process is exacerbated by component systems that don’t include drivers with adequate bandwidth to work well together.

If you want the music reproduced by your car audio system to sound amazing, drop by your local specialty mobile enhancement retailer and ask them what’s available for your vehicle. Be sure to audition one of their demo vehicles to ensure that they can deliver the performance you want. It’s not unlikely that they’ll suggest an amplifier or signal processor that includes bandpass filtering to make everything sound great.
This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

Dash pods, kick-panel enclosures and sealed enclosures in doors might look cool, but they aren’t always an ideal solution for a speaker that will attempt to produce bass. In this context, when we talk about bass, we are discussing audio frequencies below about 300 Hz. In this range, most drivers with a cone diameter of 4 inches or more can play down to around 125 Hz or lower. If the enclosure used with the speaker is too small, you’ll end up with unwanted distortion and limited low-frequency extension.

Modeling Speaker Behavior

Anytime a speaker will be used at frequencies below 300 Hz, we need to ensure that there’s enough air volume behind the driver so as not to affect the overall system compliance. In a sealed enclosure, air acts as a spring. This spring adds to the compliance of the speaker to form a high-pass filter. Yes, we have the benefit of increased physical power handling, but we trade bass output.

For this example, we’ll use a 6.5-inch midrange driver that’s been designed for infinite-baffle installations in the doors of a car or truck or on the rear parcel shelf of a sedan. The graph below shows the driver’s predicted frequency response in an enclosure with an air volume of about 3 cubic feet. This enclosure is large enough to simulate an infinite-baffle installation.

In this application, the driver’s -3 dB point is acceptable at 89.15 Hz, and the system has a Q of 0.672. Both calculations indicate that this mounting location will work superbly when combined with a subwoofer.

Small Speaker Enclosures

What if someone who doesn’t have experience using speaker modeling software decides they want to install this speaker in a pod in the kick panel of a car or, worse, on the vehicle’s dash? Let’s be generous and assume this pod has an internal air volume of about 2 liters or 0.07 cubic feet. What happens to the frequency response of our mid-woofer?

Our enclosure modeling software shows a peak of 4.5 dB at 236 Hz. The system Q has jumped to an unruly 1.605. Equally troublesome is the fact that bass output has been reduced dramatically. This small pod has choked the woofer, and it’s now producing 10.3 dB less output at 90 Hz.

Can We Fix This With an Equalizer?

To the uninitiated, it would seem that applying some equalization might fix the problem. If we keep the volume levels low, we could theoretically add some low-frequency equalization to compensate for output at 90 Hz. With that said, we’ll need to send almost 11 times as much power at 90 Hz for the same amount of output in a properly-sized enclosure.

Unfortunately, while we can tame the peak at 235 Hz, we can’t eliminate the resonance that caused it and the associated distortion. When the cone assembly’s mass, the compliance of the suspension and the compliance of the air in the enclosure interact, there’s a frequency where a small amount of input produces a disproportionally large amount of output. We call this the resonance frequency.

The Qtc value describes the size of the resonance. When looking at Thiele/Small parameters and calculating a driver’s behavior and an enclosure, the Qtc, or Total System Q tells us how prominent a peak in response is. It’s a unitless number in SPL, but software like BassBox Pro or Term-PRO can offer an accurate prediction.

In most cases, we want to keep the Qtc value under 0.8 or maybe 0.9 to limit distortion. These suggested limits apply to woofers in speaker pods as well as subwoofers in their enclosures. If you want your music to sound tight and controlled with no resonance or ringing, then choosing a large enough enclosure is crucial.

Pick the Right Speakers for Your Application

Suppose the audio system design for your vehicle calls for relatively large mid-woofers (4 to 6.5 inches) to be mounted in an enclosure. In that case, it’s paramount that you work with the shop to make sure the enclosure will be large enough or to pick a low-Q driver. As a second example, we model the behavior of a 6.5-inch woofer with a Qts of 0.48 in the same two enclosures.

Why Midrange Distortion Is Objectionable

If you were to talk into a real-time audio analyzer, you’d find that most male voices have the majority of their energy focused between 100 and 1000 Hz. If there’s any emphasis or distortion through this range, voices will sound unnatural and unbalanced.

Ultimately, designing a car audio system upgrade requires that the Product Specialist and installer you are working with balance speaker size with the available mounting locations in your vehicle. If a pod needs to be built, you may find that a smaller speaker will deliver a smoother frequency response with less distortion. It’s counterintuitive, but that’s just the way it works.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

Since 1953, the Chevrolet Corvette has been an icon in the North American automotive industry. These two-seaters represent value and performance with styling that always lets them stand out from the crowd. Try as General Motors might, there’s still room for improvement, even on a flagship vehicle like this. Let’s look at some of the upgrades available to improve the performance of the audio system in a Corvette and accessorize the vehicle to make it more functional and look better.

Corvette Audio System Upgrades

Whether your Vette came with an analog radio mounted on its side (a la C2) or a touchscreen multimedia receiver in a C7 or C8, the audio system performance in these cars has never been something to write home about. Thankfully, the aftermarket is here to support your quest for superb sound with hundreds of upgrade options.

Companies such as Custom Autosound Manufacturing and RetroSound offer twin-shaft radio designs that will work with your C1 through C3 Vette. These radios include a modern digital AM/FM tuner, Bluetooth and SiriusXM satellite radio compatibility when combined with an SXV300 tuner module. A USB port will let you connect your iPhone or use a USB memory stick to digital audio files. Best of all, these radios include preamp outputs that allow your installer to add high-power amplifiers to bring your music to life.

For C4 through C6 Corvettes, the options for radio upgrades increased dramatically. Chevrolet used a more conventional design that paved the way for hundreds of radio upgrade options for music enthusiasts. The latest generation of floating-face radios are prime candidates for adding Apple CarPlay and Android Auto to your sports car.

If you have a C7 Vette with a Bose audio system, you can upgrade the vehicle with high-quality amplifiers and speakers using a MOST radio interface such as the M650-GM from NAV-TV. This interface will extract a full-range audio signal from the digital connection between the radio and the factory amplifier. This signal can be fed to a digital signal processor and your choice of an amplifier to create an amazing audio system.

Add a Subwoofer for Great Sound

If you’ve been a reader of BestCarAudio.com for any length of time, then you’ll know that adding a subwoofer to your car is easily one of the best bang-for-your-buck upgrades you can make. Corvettes can most certainly benefit from better bass response.

Of course, you’re going to want a subwoofer solution that works with your vehicle. JL Audio offers several Stealthbox vehicle-specific solutions that are exclusively designed for the Corvette. These fiberglass enclosures are molded to fit the contours of your car perfectly. The result is excellent bass in a solution that installs in about an hour.

Park Safely with a Backup Camera

If you’re having a multimedia receiver installed in your Corvette, ask about adding a backup camera. With their low seating position and relatively high rear bumper, Corvettes can make it difficult to see what’s behind your car. If you aren’t changing the radio, you can always have the rearview mirror upgraded with a unit that includes a color display for a camera.

Sound Deadening Makes Driving Comfortable

If you are using your Vette as a daily driver, then you might want to consider having the doors, floor and hatch area treated with a layer of sound deadening. This butyl material absorbs sound energy and makes driving quieter and more comfortable. If you use Bluetooth hands-free systems or a smartphone integration technology like CarPlay or Android Auto, having a quieter car will make your voice easier to be heard.

Radar Detectors and Laser Defense

Who would buy a Corvette only to drive it slowly? If you find you have a bit of a lead foot, you might want to inquire about having a radar detector and laser defense system installed. Radar detectors are available in portable units that are great for quick installation and transportation from one vehicle to another.

For the ultimate protection solution, consider a custom-installed radar detector and laser defense solution. The biggest benefit of a custom system is the availability of laser defense technology. As more and more police forces equip their officers with lidar instead of radar, you need laser shifters to help prevent tickets.

Window Tint and Paint Protection Film

Having the windows of your car tinted offers three benefits. First, tint protects your skin from the harmful effects of the sun’s UV rays. If you spend a lot of time in your car, tint can help to prevent wrinkles, blemishes and, in extreme cases, skin cancer. The same properties that protect your skin also protect the fabrics, leathers, vinyl and plastics in your vehicle. Colors won’t fade anywhere near as quickly, and plastics won’t dry out and crack.

Second, window tint is a great way to help keep the interior of your vehicle cool. Tint films such as 3M Ceramic IR and Crystalline block 97% of the sun’s infrared energy. If you live in an area that’s hot during the summer, heat-blocking window film is a great investment.

If you care about how your Corvette looks, then window tint can dramatically improve the style of your sports car. A nice dark tint can be very dramatic.

Speaking of great looks, you may want to consider having your car protected with a layer of paint protection film. Also known as clear bra, this transparent urethane film applies directly over the paint to offer a layer of protection from stone and gravel chips, bug splatter and stains from road tar. While most installations focus on protecting the front bumper, fenders and hood, other areas that deserve attention are the rocker panels, doors, mirror covers, and the area around the hatch. If you take your Corvette to the track, protecting the rear fenders from gravel and rubber chunks thrown up by the rear tires is a great idea.

Remote Starters Add Comfort

Another great option for those living in areas of the country that get painfully hot is a remote car starter. Though more commonly associated with freezing winter conditions, remote starting your car a few minutes before it’s time to go will let the air conditioning system start cooling the interior.

We know that your Corvette is your pride and joy. It’s important to protect it and keep it safe. If you’ve opted for a remote starter system, then ask about adding security features such as a high-output siren, a remote with two-way communication or a GPS tracking option that works with your smartphone. If your car is moved without your authorization, the tracking system will send an alert to your smartphone, and you can check its location and notify the police if necessary.

Dashcams Add Protection

Whether you’re worried about how the drivers around you behave, or you want to keep track of who or what is prowling around your car when it’s parked, having a dashcam installed is a great upgrade. These compact digital video recording systems install on the front windshield of your car. If there’s an accident, fraud or just something amazing happening in front of your vehicle, you’ll capture it all on video. Many dashcams can be upgraded with rear-facing cameras, and many include GPS options and built-in accelerometers.

LED Lighting Adds Fun and Safety

If you have an older car with incandescent headlights, drop by your local specialty mobile enhancement retailer and ask about high-performance LED replacements. Not only do LED bulbs put out significantly more light, but they are also more efficient. With less draw on your electrical system, the alternator will be happier. Ask the retailer you’re working with to spice up your Vette with some LED lighting. Headlight rings, such as those popularized by BMW, are a popular upgrade. Of course, multicolor LED lighting strips are a great choice for personalizing your engine compartment or footwells or for adding under-car lighting.

Upgrade Your Corvette Today

Whether you’re driving a Corvette that’s fresh off the showroom floor, the car you had in college or a custom restoration, your local specialty mobile enhancement retailer has thousands of options to update your vehicle. Drop by today and talk to them about new communication technology, a better sounding stereo system or a lighting upgrade.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.