Installing mobile electronics in a vehicle is a balance of technical skill and creativity. From the seemingly simple task of connecting wires to the creation of a custom amp rack or subwoofer enclosure, each task requires the car audio installation technician to call upon many different skills. When it comes to installing audio gear in your car, many retailers offer packaged solutions at different performance levels for their clients – this is often called the Good, Better, Best approach. In this article, we look at a few examples where this approach is commonly applied and examine the benefits for each.

Door Speaker Installation

It sounds simple, doesn’t it? Take off the factory door panel, unscrew a speaker, connect the new one, then screw it in place. Finish up by putting the door panel back on. For the average mobile electronics retailer, this would just barely qualify for a “Good” installation. With the speakers connected and installed, the installer typically will have a listen to the system before putting it all together to confirm all the wiring is correct. If you require a speaker adapter, the shop may offer to supply one made from painted wood or crafted from HDPE or ABS plastic. Always take the plastic adapter. Wood will swell up when it gets wet.

For those looking for a “Better” installation, several companies offer speaker mounting baffle rings. These are foam rings that surround the speaker and seal the mounting surface to the back side of the door trim panel. This ring can help with the transfer of sound energy into the vehicle and is likely to reduce the chances of buzzes and rattles. Your installer may also place a sheet of damping material behind the speaker – 12×12-inch pieces are common. This material helps to damp the metal to which the speaker is mounted and ensure there is no gap between the speaker and the mounting surface.

In a “Best” quality installation, the installer will cover the entire surface of the door in a high-quality damping material. Sealing up the access holes in a door panel can dramatically improve the low-frequency response and overall efficiency of the speakers you are having installed. In fact, money spent on proper damping offers a bigger gain in performance than an equivalent upgrade in the quality of speakers.

Several companies offer composite damping solutions that combine damping with a layer of closed-cell foam. This type of damping material offers a further reduction in buzzes and rattles, and improvement in sound absorption.

You may opt to have damping material installed on the outside door skin while the trim panel is off. Damping the outer door skin will further reduce the transfer of outside noise into your vehicle, making your audio system easier to enjoy. If you are using a moderate- to high-power amplifier, you may also opt to have new speaker wires run into the doors.

Subwoofer Enclosure

One of the first upgrades you should do to your audio system is to add a subwoofer. Almost every factory audio system, even one that includes subs, sounds anemic and weak.

When it comes to the choice of subwoofer enclosure, the options are nearly limitless. The most basic of subwoofer enclosure solutions is to pick a pre-fabricated enclosure from a catalog, have your installer install the sub and plunk it in your vehicle. This solution doesn’t qualify for our standard of “Good”, but it works, and it’s better than not having a sub at all.

Choosing to have your retailer design an enclosure specifically for the subwoofer you have chosen and the exact space you require moves us up to the “Good” standard. The enclosure should be made of 3/4″ MDF and finished in a material that matches your vehicle. It should maximize the available room in your vehicle reasonably well.

The move to the Better level may take different directions, depending on your vehicle. Fiberglass or Stack-Fab enclosures can further maximize the available space in your vehicle. If constructed correctly, these enclosures can be more rigid thanks to additional bracing. This bracing results in better performance. At the “Better” level, your installer may choose to incorporate some cosmetic accents. Including a trim ring around the sub in an accent material is pretty common.

At the “Best” level, the enclosure design will be topnotch! Your installer may even choose to measure the Thiele-Small parameters of your subwoofer before starting work. The enclosure will be extremely rigid and well-reinforced internally.

Your installer may choose to line or stuff the enclosure with materials like Dacron or foam. Cosmetics will also take a leap forward at this level. Having the enclosure trimmed flush to the sides of the vehicle is a must to make it look like it came from the factory. Your installer may choose to use vinyl or leather on the visible parts of the enclosure to further improve the match with factory styling. A product or vehicle brand or logo may be incorporated into the design as well. At the Best level, anyone who sees the resulting creation should be immediately impressed.

Design and Cost

There is no limit to how creative your installer can get with the installation – it’s all governed by how much you want to spend. At the higher end, the installer may provide drawings or sketches of the finished product. You will probably have to pay for this design time. That said, many shops will credit some or all of that back to you as part of the final cost.

The top installers around the country charge upwards of $100 per hour for custom work or more. Their experience and creativity allows them to be very efficient in executing their ideas, and the work behind the scenes is often equally exemplary. Attention to detail for wiring, product mounting with Nutserts or stainless steel hardware, and proficiency in system design and tuning are all part of getting the Good, Better or Best value for your money.

Visit Your Local Specialist For Car Audio Installation

When it’s time to go shopping, drop by a few of your local mobile electronics specialist retailers. They would be happy to show you different options for your project.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

Among the most under-appreciated components in any audio system are the speakers. You could be using the best source unit on the planet, an amazing amplifier, and the most esoteric of interconnects and speaker cables – but if you don’t have great speakers, you still won’t have great sound. Your speakers are the only link between your electronics and your ears, so choosing great speakers is critically important to reproducing great sound. This article discusses what you get when you spend more money on speakers.

More Power Handling

Several factors limit the ability of a speaker to convert an electrical signal into speaker cone motion. One such limit is thermal capacity – just how much heat the voice coil, tinsel leads, former and cone can handle before one of them fails. Heat is the number-one enemy of speakers. Most of the power you send to your speakers is converted to heat rather than to sound – in fact, probably 95% or more is converted to heat.

As the quality of speakers increases, you often encounter a larger voice coil and better cooling technologies. These features, coupled with tighter tolerances around the voice coil, result in a speaker that can absorb more energy without failing.

More Excursion

Often tied directly to how much power a speaker can handle is the distance the speaker cone can move forward or back. This specification is called excursion. For most speakers, the specification for excursion is called Xmax. Xmax is the distance the cone can move in one direction without the voice coil moving out of the magnetic field, and the measurement is typically provided in millimeters.

A second and often equally important specification is Xmech or Xsus. These specifications describe the physical limit of how far the cone can move, based on the design of the suspension (spider and surround). A speaker can be pushed past the Xmax limit, but as this happens, distortion occurs. When a speaker cone reaches its physical excursion limit, distortion will spike even higher. When it comes to speakers, there is no good distortion, so operating them within their physical limits is critical to producing accurate sound.

Why is excursion important? When combined with the ability to handle more power, a “better” speaker will play louder when provided with more power. The same features also help to reduce a phenomenon called power compression. Power compression is a reduction in the efficiency of a speaker as its components heat up. The key drawback to power compression is that when the music gets quieter, you turn the volume up, thereby sending more power to the speaker and accelerating the heating effect. In no time, the speaker will fail.

Excursion Linearity

It’s one thing for a speaker to have good power handling and excursion characteristics. It is equally important that the speaker remains linear throughout its excursion-based operating range. All speakers change in their characteristics as excursion increases – a great speaker minimizes these.

Let’s look at a common problem with “simple speakers.” One of the characteristics that limit the high-frequency response of a woofer or midrange driver is inductance. The voice coil of the speaker has some natural inductance because, well – it is a coil of wire. This inductance is increased when we place the voice coil around the T-yoke of a speaker.

This is where the problem occurs: As the coil moves forward, some of it may leave the T-yoke, which will reduce inductance. As the coil moves rearward, inductance may increase. The result is that the speaker has different frequency responses depending on where it is within its range of excursion. Truly excellent speakers use technologies to minimize these effects. The result are speakers that sound just as good at low to moderate drive levels as they do when being pushed hard.

More Frequency Response

This is a bit harder to describe, because sometimes the improvement from a basic to a mid-priced speaker, or a mid-priced speaker to a high-end one, is extended frequency response. More often, it’s smoother frequency response. Better-quality speakers are, ideally, designed to reduce distortion caused by cone resonances, suspension nonlinearities and magnetic field imbalances. As you spend more on speakers, you will see that peaks in their frequency response, especially in the midbass region, are tamed.

Many great speakers still exhibit some cone resonances at high frequencies. As long as the speaker you are using in the adjacent band will play low enough, those peaks are not critical.

Reduced Distortion

When a speaker designer combines an appropriately damped and rigid cone with a carefully designed motor and suspension, the result is a speaker that produces less distortion. Some distortions are very subtle, while others are quite pronounced. Speakers exhibit both even- and odd-ordered harmonic distortions, depending on what component or design issue is to blame.

If you have read our article on distortion, then you know that it is the effect of adding content that was not in the original program material. Harmonic distortion results in even or odd multiples of a specific frequency.

When you hear an amazing speaker, the difference between it and an average speaker is clarity. Smooth frequency response and a lack of distortion make each sound the speaker produces more faithful to the recording. Voices will sound more realistic. Instruments will sound more natural. Complex passages will become easier to understand.

It is also critical to point out that distortions cannot be removed from a signal or sound once created. No amount of equalization can extract those harmonics. Yes, you can reduce their level, but you also reduce the level of original signal information at those same frequencies. The only solution is to use a speaker that does not introduce distortion.

The Right Tool for the Job

Another item that differentiates a good speaker from a great one is its design in terms of application. Let’s use a typical 6.5” midrange/midbass speaker as an example. If the speaker is designed to work in a typical door or rear deck-style installation, the Thiele-Small parameters for that transducer will be optimized for that application. If you attempt to put that speaker into a small kick panel pod that has only 0.1 cubic feet of air space, you will choke it. The low-frequency response will be dramatically reduced; typically, a bump in the midbass region will occur, and it will likely not sound very good. Most 6.5” speakers need an enclosure volume of about 0.6 cubic feet, and some want closer to 1.0 for smooth frequency response.

How do you look for a speaker designed for the right application? That is product knowledge that a properly trained mobile electronics retailer can provide. Do you need a midrange that will work in a small A-pillar pod? Do you need a woofer that will work in an infinite baffle application? Will your midbass driver be used with a subwoofer, or do you need one that will be the sole source of bass in the system? Knowing the intended application for a speaker ensures that the system designer will use it appropriately.

Are More Expensive Speakers Always Better?

Does price always determine performance? In the upper echelon of any audio industry, the rewards for spending exponentially more money diminish. That is to say, the improvement you get from spending $500 on a set of speakers as compared to $200 may not be as dramatic as the difference between $2,500 and $2,200.

Every speaker manufacturer wants you to buy their speakers. They all work hard to come up with great marketing programs to make you want to buy their products. Your goal in choosing an amazing speaker is to ignore the story and listen.

The best way is first to establish a reference. Listen to the best speakers you can find. Don’t worry about the price. You simply want to understand what is available. Then, choose your price point and listen to something in that range. If you can accept the differences, then proceed. If you can’t, re-evaluate your needs or your budget. You can’t get that extra level of clarity, dynamics and detail any other way.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

According to a AAA survey, the average American drives for about 45 minutes each day. If you compare this time to an eight hour work day, that’s 10% of your work day, on top of the hours you are at your desk. This time is not an insignificant number. If your job involves being on the road, then your time spent behind the wheel can represent half of your day. Being able to be productive while in your vehicle is not only convenient, but in some cases, mandatory to get all the work you need to get done in one day completed. Modern smartphone integration comes to the rescue with Apple CarPlay.

Apple CarPlay History

Apple recognized the need to give people the ability to use their phones in a safe fashion while driving back in 2010. The feature was called iPod Out. BMW announced that it would include iPod Out at the WWDC that year. The concept was that BMW would provide a way for its vehicles to ‘host’ specific applications. The information would be displayed on the factory screen while providing button press and knob rotation information back to the radio.

The next evolution was the introduction of Siri Eyes Free in some Honda Accord and the Acura RDX and ILX models in 2013. Siri Eyes Free is a way to make use of the Siri voice recognition function that Apple Introduced with iOS 5 and the iPhone 4S in October 2011. Apple has marketed Siri as a personal assistant. It allows you to talk to your Apple device to make phone calls, send text messages, set reminders and choose the music you want to hear. Using Siri Eyes Free is simple- press and hold a button on your car radio, wait for the tone, and then speak.

Siri will listen to what you said, convert that to a command and execute it, all without you needing to take your eyes off the road.

Between the time that Apple announced iPod Out and the Geneva Motor Show in March of 2014, Apple was working on the next generation of automotive integration under the code name Stark. At the Geneva Motor Show, they announced ‘iOS in the Car.’ Later that year, Ferrari introduced the new FF model with a fully working version of Apple CarPlay. A few months later, Hyundai announced the Sonata would also feature CarPlay. Most automobile manufacturers have CarPlay available on their mid to high trim level vehicles now.

Apple CarPlay Interface Overview

Apple’s current marketing touts CarPlay as ‘The Ultimate Copilot.’ The features are designed to allow you to communicate with family, friends, and coworkers without significant distraction. The basic feature set of CarPlay includes making and receiving phone calls, choosing the music you want to listen to, getting navigation instructions and sending and receiving text messages.

Apple has worked hard to ensure that the above functions are usable without unnecessary distraction. As soon as you plug your phone into the USB port of your radio, CarPlay launches automatically.

CarPlay does not display incoming text messages on the screen of the radio. Messages are read aloud to prevent users from looking at the dash. However, there are no options presented when asking Apple Maps to plan a navigation route.

Selecting music to play is as easy as requesting the track title, artist or even genre of music you want to enjoy. CarPlay will start playing what you want right away. Apple has also included support for Apple Music- a streaming service powered by iTunes. CarPlay also supports Apple Podcast and Audiobooks. You can select the episode you want to listen to via the touchscreen interface, then play, pause or skip 15 seconds forward or back. Apple CarPlay provides support for several third-party applications including Pandora, Spotify, iHeartRadio, Audible and MLB At Bat.

Apple has released information to application developers in order to allow for the creation of more third party applications. You will see more and more third-party applications added to the CarPlay interface as time passes. Apple will, of course, be selective in their approval process, so don’t expect to see competing navigation applications any time soon.

The Future of Apple CarPlay

Unveiled by BMW in October of 2016, future iterations of CarPlay will function wirelessly. The 2017 BMW 5-Series sedans, when used with an iPhone 6 or newer, will allow users to use CarPlay without the need to plug in the Lightning connector. Wireless CarPlay communicates over a Bluetooth data connection.

Apple is tight-lipped about future functionality of CarPlay. There have been rumours about vehicle function control like remote door lock control, remote starting and trunk release, but so far nothing is set in stone. Another rumored feature is the ability of your phone to remember where you parked your car once you have arrived at your destination.

Apple has led the industry with safe and convenient integration of your smartphone to your vehicle. The future of ‘connected cars’ promises to allow us to share information and offer better communication while remaining safe. If you are interested in adding CarPlay to your vehicle, visit your local mobile electronics specialist retailer. They can show you what options are available for your vehicle.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.